Router configuration:
Router A
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int f0/0
Router(config-if)#ip add 150.160.12.1 255.255.0.0
Router(config-if)#no shut
09:31:10 %LINK-3-UPDOWN: Interface Fastethernet0/0, changed state to up
09:31:10 %LINEPROTO-5-UPDOWN: Line protocol on Interface Fastethernet0/0, changed state to up
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/0
Router(config-if)#ip add 10.10.10.1 255.0.0.0
Router(config-if)#no shut
09:32:09 %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
09:32:09 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/0
Router(config-if)#clock rate 64000
Router(config-if)#bandwidth 64
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router B
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/0
Router(config-if)#ip add 10.10.10.2 255.0.0.0
Router(config-if)#
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int f0/0
Router(config-if)#ip add 200.200.150.4 255.255.255.0
Router(config-if)#no shut
09:44:10 %LINK-3-UPDOWN: Interface Fastethernet0/0, changed state to up
09:44:10 %LINEPROTO-5-UPDOWN: Line protocol on Interface Fastethernet0/0, changed state to up
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/0
Router(config-if)#int s0/1
Router(config-if)#exit
Router(config)#int s0/1
Router(config-if)#ip add 11.10.10.3 255.0.0.0
Router(config-if)#no shut
09:46:03 %LINK-3-UPDOWN: Interface Serial0/1, changed state to up
09:46:03 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up
Router(config-if)#
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/1
Router(config-if)#clock rate 64000
Router(config-if)#bandwidth 64
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router C
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int f0/0
Router(config-if)#ip add 220.220.200.4 255.255.255.0
Router(config-if)#no shut
09:48:47 %LINK-3-UPDOWN: Interface Fastethernet0/0, changed state to up
09:48:47 %LINEPROTO-5-UPDOWN: Line protocol on Interface Fastethernet0/0, changed state to up
Router(config-if)#
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#int s0/1
Router(config-if)#ip add 11.10.10.4 255.0.0.0
Router(config-if)#no shut
09:50:39 %LINK-3-UPDOWN: Interface Serial0/1, changed state to up
09:50:39 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up
Router(config-if)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
IP Routing:
Router A
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#ip route
% Incomplete command.
Router(config)#ip route 200.200.150.0 255.255.255.0 10.10.10.2
Router(config)#ip route 0.0.0.0 255.255.255.255 11.10.10.4
Router(config)#
Router# copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#router rip
Router(config-router)#network 150.160.0.0
Router(config-router)#network 10.0.0.0
Router(config-router)#network 11.0.0.0
Router(config-router)#version 2
Router(config-router)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router B
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#ip route 150.160.0.0 255.255.0.0 10.10.10.1
Router(config)#ip route 0.0.0.0 255.255.255.255 11.10.10.4
Router(config)#
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#router rip
Router(config-router)#network 200.200.150.0
Router(config-router)#network 10.0.0.0
Router(config-router)#network 11.0.0.0
Router(config-router)#version 2
Router(config-router)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router C:
Router Con0 is now available
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#ip route 150.160.0.0 255.255.0.0 10.10.10.1
Router(config)#ip route 0.0.0.0 255.255.255.255 11.10.10.3
Router(config)#router rip
Router(config-router)#network 220.220.200.0
Router(config-router)#network 11.0.0.0
Router(config-router)#version 2
Router(config-router)#
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Now,
Ping 220.220.200.2
Router Con0 is now available
Press RETURN to get started!
Router>ping 220.220.200.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 220.220.200.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
Router>
_______________
No comments:
Post a Comment